Of all the options there are, if you need a firearm for protection or hunting quickly, then making a zip gun might be the answer. It will give you the immediate means of protection and allow you more time to make something better, or to use it to obtain better equipment, including genuine firearms.
An AR assembled at home, a gun built from a kit, a 1911 pistol patiently hand-fit to match tolerances are technically homemade. However, so is a crude amalgamation of scrap metal that would make a Sten gun look like the Mona Lisa.
As firearms technology progressed, so too did the skills required to make them. Fire lances evolved into metal-cast hand cannons, requiring blacksmithing knowledge to produce. These gave way to smoothbore muskets, featuring increasingly complex ignition mechanisms.
In a very general sense, to make a zip gun you must first find some sort of tube with a method to seal the breach. The next step is adding some sort of firing mechanism and maybe even some way to hold onto the thing.
The simplest zip gun design that one can make is a slam fire pipe gun, which uses a common metal pipe with a threaded end and a pipe cap. You tap a hole in the center of the pipe cap and put a nail in there.
The kit gives you some of what you need to make a slam fire pipe shotgun that fires .410 bore shells, specifically the barrel which has a fitting with a captured firing pin. It's fairly similar in function to the Richardson slam fire guerilla shotgun shown above but uses different, more commonly available parts.
Improvised versions are made by using two pipes and an end-cap; they usually fire shotgun shells. To fire the gun, the user inserts a shotgun shell into the smaller diameter pipe, places the smaller pipe into the larger diameter pipe, and forcefully slides it back until the shell's primer makes contact with a fixed firing pin located inside the end-cap.
While most improvised firearms are single-shot, multiple-shot versions are also encountered. The simplest multi-shot zip guns are derringer-like, and consist of a number of single-shot zip guns attached together. The pepper-box design is also used in homemade guns because it is relatively easy to make out of a bundle of pipes or a steel cylinder. In late 2000, British police encountered a four-shot .22 LR zip gun disguised as a mobile phone, where different keys on the keypad fire different barrels. Because of this discovery, mobile phones are now X-rayed by airport screeners worldwide. Authorities believe they were manufactured in Croatia, and they still turned up in Europe as late as 2004, according to a report by Time magazine.
Danao City, in the Cebu province of the Philippines, has been making improvised firearms so long that the makers have become legitimate, and are manufacturing firearms for sale. The Danao City makers manufacture .38 and .45 caliber revolvers, and semi-automatic copies of the Ingram MAC-10 and Intratec TEC-DC9.
One of the obvious flaws of such guns is the limited firing range that does not make them a weapon of choice in high stake operations. However, such weapons are often used at places of higher restrictions and surveillance, such as prisons, and can be used to cause lethal damage in close proximity.
For other states, please check your law on this matter before deciding to make a zip gun by yourself: it is highly probable that some of them will give you an opportunity to keep a zip gun for personal use, but not for others.
Once again, please remember to check your federal law on this matter before starting to make zip guns in the conditions far from survival ones, as you need to comply not only with the fact of having approval for personal use or not but also with the way that the pistol should be constructed and what could be done with it inside your state and outside of it as well.
When choosing this construction of your improvised firearms with .22 cartridge, make sure that you have positioned a screw tightly to the rim of the cartridge after drilling the elastic metal strip. For a larger diameter of bullets, the screw should be placed near the primer of a centerfire cartridge. For both cases, remember to also cut the point off of the screw.
This choice might be more time-consuming, but at the same time, it will also be more efficient, as you will have an opportunity to choose power blanks by yourself, and buying the most powerful ones will definitely make your single shot faster. However, if not able to find such, weaker options will still give you an opportunity to kill something like a rabbit.
For example, it is even possible to make an actual gun, like the ones that you see at the stores, with your own hands. However, it is, of course, not an option for everyone, as it is definitely more time-consuming and harder to make: you will need more tools, more knowledge, and more patience.
Consequently, in situations when you cannot rely on the police to protect you and your family, you will need to take matters into your own hands and either buy a shotgun or make one at home. In cases when you do not have money to buy a gun or there is simply nothing left at the stores, creating a zip gun will be your best choice.
In this article, we are not persuading you to go and break your laws by creating a handmade firearm, no. The only point that we make here is that you just need to know how to protect yourself in rare case scenarios when relying on the police is simply not enough. Remember that having a self made pistol is illegal in many places, thus, you will either end up in jail or with a big fee to be paid off, with your guns being seized in any case.
However, if you want to find a measure for protecting yourself even now, we would not recommend you to make firearms without checking your laws first. In case when you are not allowed to keep self-made firearms, it is always better than to buy more traditional weapons in some hardware store then to try your luck with getting caught by the police.
For the past almost half-century, however, the sale and subsequent control of firearms have been heavily regulated by federal law. It might come as somewhat of a surprise that even in this era of regulation, it's still completely legal to make and own a homemade gun (also called a self-assembled or privately made gun). Even more surprising, in most states, a gun made wholly or even twenty percent at home need not be registered, and the owner need not pass a background check or obtain a license.
However, the Court has also acknowledged that the Second Amendment does not confer an unlimited right, and that lawmakers can still impose regulations, such as forbidding some people from possessing them (felons, for example); prohibiting them in places such as schools and government buildings; and imposing conditions and qualifications on their sale, licensing, and regulation.
The federal Gun Control Act of 1968 (GCA) requires, among other things, that persons "engaged in the business" of dealing in firearms be licensed by the federal government. This law made it illegal for an unlicensed person to make a firearm for sale or distribution. In addition, the law requires firearms dealers to perform background checks on people who want to buy a gun, and to maintain records of all gun sales. (18 U.S.C. § 921(a)(21)(C);18 U.S.C § 922(t); 18 U.S.C. § 923 (2022).)
However, nothing in the GCA prohibits individuals from making guns for their own personal use. A non-licensed person may make a firearm, provided it's not for sale and the maker is not otherwise prohibited from possessing firearms. (18 U.S.C. § 922 (d) (2022).) Federal law imposes none of the purchase restrictions on non-licensed possessors that it does on those who need licenses, and as a result, the homemade gun owner need not undergo a background check, and the gun doesn't have to be registered unless a state law requires registration. (For more information on state laws regulating ghost guns, see the section below "Are Ghost Guns and 3D Printed Guns Legal?")
While it has always been legal for people to make homemade guns, in practical terms the process hasn't been so easy. A gun is a highly machined piece of equipment, dependent on precise specifications and materials. Most individuals making firearms at home historically lacked the equipment and know-how necessary to make a sophisticated piece of weaponry. However, modern technology has addressed many of these challenges, by offering "partial receivers" and the ability to make a gun using 3D printing.
A person interested in avoiding a background check and gun registration can instead buy an unfinished receiver (also called an 80%, blank, or partial receiver) to make a "ghost gun" (so called because it can't be traced). An unfinished receiver is a partially completed receiver that requires additional tooling to be fully completed. This kind of receiver is not technically a firearm and is not regulated by the GCA (and so does not bear a serial number). Unfinished receivers are legal to sell in most states and are widely available online and at gun shows.
Unregulated receivers can be converted into working firearms by someone with very basic skills and tools. A purchaser uses a drill press to create holes in the receiver and adds other parts to make a fully functional gun. Finishing kits and how-to guides are extensively available online and through specialty markets. Many sellers host "building parties," where buyers come together to share tools and expertise and assemble their firearms. Ghost guns created with unfinished receivers range from basic handguns to semi-automatic weapons.
People can also make homemade firearms using 3D printers. 3D printing, also known as "additive manufacturing," is a process whereby a three-dimensional model designed on a computer becomes a three-dimensional solid object as the printer lays down successive layers of material that conform to the programmed instructions. Gun parts, predominately made of plastic, can be generated from 3D printers. 2b1af7f3a8